Buyer's Guide

Capsule House Vietnam Salt Air Corrosion Guide

Capsule house salt air corrosion in Vietnam: what salt attacks first, exposure distance, coating and fasteners, sacrificial items and the rinsing regime.

Capsule cabin on a headland above a Vietnamese bay with fishing boats and sea spray

Capsule house salt air corrosion on the Vietnamese coast is a specification problem that shows up as a maintenance problem two or three seasons later. Salt-laden air travels, settles on every surface, and stays damp in a humid climate; the corrosion it causes is concentrated at fixings, joints and edges rather than spread evenly across the panels. This page covers the practical sequence a coastal buyer should work through: what salt attacks first, how distance from the shoreline and exposure set the specification, coating and fastener selection, which items to treat as sacrificial and replace on a schedule, the washing and inspection regime, and the records that make a corrosion conversation with a supplier productive. Country planning is in the capsule house Vietnam guide, budget context in capsule house price in Vietnam and the general capsule house price page. Wind and storm engineering is a separate subject and stays in typhoon planning for capsule houses in Vietnam.

What salt attacks first

Corrosion does not begin in the middle of a panel. It begins where a protective layer has been interrupted, where two different metals meet, or where water sits. On a prefabricated unit the predictable starting points are:

  • Fixings. Screws, bolts and rivets are the first items to show rust, because they are small, they are usually a different metal from what they fasten, and they are installed by cutting through a coating.
  • Cut edges and drilled holes. Every penetration made on site is an uncoated edge, and an uncoated edge in a marine atmosphere is where corrosion starts.
  • Joints and laps. Water sits in the lap and the salt concentration rises as it evaporates.
  • The base and the hold-downs. Closest to the ground, least washed by rain, most exposed to splash and damp.
  • Glazing frames and thresholds. Constantly wet, constantly salted, and the first thing a guest touches.
Macro view of white salt deposits crusting a stainless steel hinge and screw on a seaside facade
Salt crust on a fixing is the earliest visible signal. The fixing is replaceable; what it fastens to is not.

Exposure distance sets the specification

The single most useful question at specification stage is how far the unit stands from the shoreline and what is between it and the sea. Exposure is not a binary coastal or inland distinction. A unit on an open headland facing the prevailing onshore wind is in a different class from one five hundred metres inland behind a treeline, and the correct specification differs accordingly.

Three factors beyond distance matter: elevation, shelter, and whether the site receives salt spray directly or only airborne salt. A raised, open, windward plot gets both. Tell the supplier which of these applies, because the specification — coating build, fastener material, and the items treated as sacrificial — follows from it.

Coating and fastener selection

Coatings

Ask what the coating system is, not what colour it is: the pretreatment, the type of coating, the number of layers, and the specification it is applied to. Ask specifically what happens at a cut edge or a site-drilled hole, and what touch-up material is supplied. A unit with a sound factory coating and no touch-up provision will still corrode, because the site will drill holes.

Fasteners

Fasteners are the item to upgrade rather than the panels. Ask what material the external fasteners are, whether they are compatible with the metal they fix, and whether they are isolated where two dissimilar metals meet. Fasteners are cheap at order time and expensive to replace in place, so this is the highest-return upgrade on a coastal specification.

Dissimilar metals

Where aluminium meets steel, or a stainless fixing meets a coated panel, the contact point corrodes. Ask how the interface is isolated. This is also the question to ask about the hold-down assembly, because it is the one place where a dissimilar-metal contact sits permanently damp.

Worker rinsing a metal building facade with fresh water using a hose near the sea
Fresh water rinsing is the least costly corrosion control available, and the one most often skipped.

Sacrificial items and replacement intervals

A coastal specification works best when it accepts that some items will be replaced and plans for it. Treat these as consumable rather than structural:

ItemWhy it goes firstPlanned response
External fastenersSmall section, coating interrupted at installationHold a stock; replace at inspection rather than on failure
Gaskets and sealsSalt and UV together shorten their lifeReplace on a schedule; do not wait for a leak
Door and window hardwareHandled constantly, always dampSpecify a marine-suitable finish and hold spares
External light fittings and fixingsSmall, exposed, difficult to isolateTreat as a replaceable unit
Touch-up coatingsEvery site penetration needs itBuy with the order and apply at installation

The washing and inspection regime

Salt is only corrosive while it sits. Rinsing with fresh water is the least costly control available, and the reason it is skipped is that nobody owns it. Assign it: a defined interval, defined by exposure rather than by calendar, and recorded.

Set the interval by exposure zone. Units in direct spray from an open shoreline need rinsing far more often than sheltered units further back, and the fixings at the base and the hold-downs need attention more often than the wall surfaces, because rain does not wash them.

At each inspection, look for the earliest signals rather than the obvious ones: rust staining running from a fixing, a bloom under a coating at an edge, a stiff latch, and salt crust at a joint. Each of these is cheap at that stage and expensive one season later.

Where corrosion and storm resilience overlap

Two subjects touch and should be separated cleanly. Wind and storm design is about whether the structure and its connection to the ground survive a defined event; it is a structural question and it is covered separately. Corrosion is about how long the materials last in a marine atmosphere; it is a durability question.

They meet at the hold-down. The assembly that resists uplift is the same assembly that sits lowest, stays dampest and is least washed by rain — so it is both the most safety-critical item and the most corrosion-exposed one. Give it the highest specification on the unit: the right material, isolation between dissimilar metals, a coating touch-up applied at installation, and a defined inspection interval. If one item on a coastal unit is upgraded, make it this one.

Records that make a corrosion conversation productive

A corrosion issue raised with a supplier is resolved faster with evidence. Four things:

  • The specification as ordered. Coating system, fastener material, and the exposure class stated in the order.
  • Installation photographs. Including the hold-downs and every site-made penetration, taken at installation rather than reconstructed later.
  • The maintenance record. Rinsing and inspection dates. A missing record will be read as missing maintenance, whether or not it was done.
  • Dated photographs of the defect. Wide enough to show location, close enough to show the detail, and taken before any cleaning.

Questions for a supplier before ordering for a Vietnamese coastal site

  1. What coating system is used, and on what specification is it applied?
  2. What material are the external fasteners, and how are dissimilar metals isolated?
  3. What touch-up material is supplied for site-cut edges and penetrations?
  4. Which items are designed as replaceable, and what is the recommended replacement interval in a marine exposure?
  5. What is the recommended fresh water rinsing interval by exposure zone?
  6. What does the corrosion warranty cover, what excludes it, and what records does a claim require?

Whether a coating system meets a particular standard is a matter to be confirmed with the supplier and verified against the issuing body; no certificate should be assumed from a description. Haishu supplies space capsule homes and expandable prefab houses and does not state certification as held — documents should be requested and verified. Requirements may vary by application, market and applicable standard.

Talk to the Factory

Ready to Ride the 2026 Wave?

Get the latest catalog, pricing tiers and a layout sketch for your land — straight from the engineering team.