Capsule House Certification: Verify CE and ISO
Capsule house certification explained: what CE, ISO and TUV actually cover, how to verify a certificate, and how to read structural reports.
"CE certified," "ISO approved" and "TUV tested" appear in modular building marketing constantly, and they are frequently used in ways that do not survive scrutiny. Some are real and relevant, some are real but apply to the factory rather than the product, and some are meaningless as written. This page explains what each of those marks actually covers, how to verify a certificate rather than accept it, and how to read the structural reports that matter more than any label. We make no claims here about which certifications any specific product holds — that is a question to put to the supplier in writing and then verify. Requirements may vary by application, market and applicable standard. You can read about how we work on our about page.
Three Marks, Three Different Meanings
The most common error is treating these as interchangeable badges of product quality. They are not the same category of document.
| Mark | What it actually is | What to check |
|---|---|---|
| CE marking | A conformity marking for products placed on the European Economic Area market, available only where an applicable harmonised standard or directive covers the product | Which directive or regulation and which harmonised standard is cited; whether the product is actually in scope |
| ISO 9001 | A quality management system certification issued to an organisation, not to a product | Certificate holder name, scope statement, issuing certification body, validity dates |
| TÜV | Not a certificate — the name of testing, inspection and certification organisations. The value is in the specific test or inspection report behind the name | Which TÜV entity, what was tested, against which standard, report number and date |
An ISO 9001 certificate tells you a factory has a documented quality management system that has been audited. It does not certify that any particular unit meets any particular performance level. A test report from a recognised body does speak to a product — but only to the specific item tested, under the specific method, on the specific date.
How to Verify a Certificate in Four Steps
Verification takes minutes and prevents the most expensive category of mistake: relying on a document that does not cover what you think it covers.
- Check the holder. The certificate must name the legal entity that manufactured the goods. A certificate held by a trading company or a different factory does not cover your supplier's production.
- Read the scope, not the headline. The scope statement defines what is covered — product categories, models, processes, sites. A scope that excludes your model means the certificate does not apply to it.
- Confirm the issuing body and its accreditation. Certificates are issued by certification bodies, which are themselves accredited. Confirm the body is accredited for the standard in question, and check the certificate number with the issuing body directly where a verification facility exists.
- Check dates and validity. Certificates have issue and expiry dates and are subject to surveillance audits. An expired certificate, or one suspended for non-conformity, is not evidence of anything.
Ask for the certificate scan and the scope page specifically. If a supplier sends a logo but not a certificate with a number, treat the claim as unverified.
Component Certificates Matter as Much as Product Ones
A finished unit is an assembly. Even where no single certificate covers the whole product, individual components often carry their own conformity documentation — and these are what a local inspector or insurer is most likely to ask about.
- Glazing: safety and performance ratings, with the standard under which they were determined.
- Electrical assemblies, protective devices and cabling: conformity to the standard required at destination.
- Insulation and any fire-rated materials: declared performance and reaction-to-fire classification where applicable.
- Coating systems and corrosion protection: the specification applied and the preparation standard used.
Request a component documentation pack with the order, not after delivery. Assembling it later is slower and often incomplete.
Reading Structural Reports
Structural documentation is more informative than any marketing label, and it is the set most buyers fail to read. Ask for these and know what each should contain.
- Design calculation report. Should state the loads assumed — dead, live, wind, snow, seismic as applicable — and the standard or code used. If the load assumptions do not match your site, the report does not cover your installation.
- Wind and seismic parameters. These are site-specific and must come from your local engineer or the applicable code for your jurisdiction. A structure calculated for a different region's parameters is not automatically compliant with yours.
- Foundation and anchorage drawings. Should give reactions at the fixing points so your engineer can design the foundation. Without reactions, your engineer is guessing.
- Transport and lifting analysis. Covers the loads the unit sees during transport and cranage, which differ from its in-service loads.
Requirements may vary by application, market and applicable standard. In most jurisdictions the unit's anchorage and foundation must be designed or reviewed by an engineer licensed in that jurisdiction. Ask your engineer to confirm the supplier's documentation is sufficient before you order, not after the unit lands.
Verification Actions You Can Take Before Shipment
Documentation is only part of it. Four actions catch problems that paperwork does not.
- Factory audit. Visit or commission an audit. Look at whether the documented process is the process actually running on the floor. Our factory audit checklist sets out what to inspect.
- Pre-delivery inspection. Inspect the finished unit against the specification before it ships, with a written snagging list and an agreed remedy. See pre-delivery inspection.
- Independent testing. Where a performance claim is critical — thermal, acoustic, water tightness, structural — commission testing by a body independent of the supplier, on a sample, against a named standard.
- Reference checks. Ask for references of units in service in a comparable climate, and ask the reference about warranty response, not just about the product.
Red Flags in Certification Claims
Certain patterns recur in marketing that does not survive checking. Recognising them is quicker than verifying every claim individually.
- A logo with no certificate number. A real certificate has an identifier that can be checked with the issuing body.
- A certificate held by a different legal entity from the one named on your contract — commonly a group company or a trading arm rather than the factory.
- A scope statement that is missing or generic. If the document does not name the product category or model, it does not demonstrably cover it.
- ISO 9001 presented as product certification. It certifies a management system at an organisation, not a unit.
- Expired dates, or a certificate issued before a model was introduced. Check the issue and expiry dates against your order.
- A test report describing a different configuration from the one you are buying — a common and easily missed mismatch.
- Refusal to supply the document itself, with only a claim offered in its place.
None of these necessarily indicates bad faith; documentation is often poorly managed. But each one means the claim is unverified, and an unverified claim should not be relied on for compliance, insurance or a consent submission. Ask for the scan, read the scope, and check the dates. Where a claim matters to your project — a conformity requirement, a fire classification, a structural rating — have it confirmed by a body independent of the supplier rather than accepted on paper alone.
What to Ask Us
Ask for the documentation pack for the configuration you are considering: component conformity documents, structural calculation basis, foundation reactions, and the warranty in writing. We will tell you what we can supply and what your local engineer or authority must determine. We publish no unverified certification claims, and requirements may vary by application, market and applicable standard. Review the Galactic A series configurations and use the contact page to request the documentation pack.
Talk to the Factory
Ready to Ride the 2026 Wave?
Get the latest catalog, pricing tiers and a layout sketch for your land — straight from the engineering team.


